今天大型機器人模型制作廠家要給大家講解一下有關于機器人模型制作的過程的知識點，希望通過我們的講解能夠更好的幫助到大家了解到這方面的知識點。

Today, the large-scale robot model manufacturer will explain to you some knowledge points about the process of robot model production. We hope that our explanation can better help you understand this knowledge point.

一、根據客戶要求及場地特點設計機器人模型效果

1、 Design robot model effect according to customer requirements and site characteristics

二、確定材質，進行小稿制作。

2、 Determine the material and make small drafts.

三、造型師按所需比例進行放大，制作骨架并對骨架（按雕塑、高度等數據）進行加固、防腐、防銹處理。

3、 The stylist shall enlarge the scale as required, make the skeleton and carry out reinforcement, anti-corrosion and anti rust treatment on the skeleton (according to the center of gravity, height and other data of the sculpture).

四、對鋼板進行整體剪裁。

4、 Cut the steel plate as a whole.

五、亞弧焊焊接，鍛打，力求做到無明顯焊縫、線條流暢、表面平整。

5、 Sub arc welding and forging shall strive to ensure no obvious weld, smooth lines and smooth surface.

六、對機器人模型進行拋光使紋理自然。

6、 Polishing the robot model to make the texture natural.

七、包裝車間根據模型大小進行分解包裝。

7、 The packaging workshop decomposes the packaging according to the model size.

八、大型機器人模型工藝流程圖

8、 Process flow diagram of large robot model

九、運輸?shù)绞┕龅睾筮M(jìn)行整體合并和相應的后期處理。

9、 After being transported to the construction site, the overall consolidation and corresponding post-treatment shall be carried out.

機器人模型制作維修注意：

Robot model making and Maintenance Notes:

將機器人模型制作表皮小面積破壞的位置用針線縫合,然后用硅酮膠均勻涂抹在縫合處,防止機器人模型制作進水,接下來再用丙烯顏料補色。

Sew the small-area damaged position of the robot model making skin with a needle and thread, and then apply silicone glue evenly on the suture to prevent water from entering the robot model making, and then use propylene pigment to supplement the color.

如果是機器人模型制作大面積的表皮損壞,需要先填充海綿,然后再用硅酮膠將纖維布粘附在上面,接下來再刷一層硅酮膠作為防水層,使用丙烯顏料稀釋以后用空壓機結合噴漆槍補色。

In case of large-area skin damage caused by robot model production, sponge shall be filled first, and then silicone adhesive shall be used to adhere the fiber cloth on it. Next, a layer of silicone adhesive shall be applied as a waterproof layer, and after being diluted with propylene pigment, air compressor and spray gun shall be used for color compensation.

在進行機器人模型制作維修時,-定要注意防火防熱,在一些鋼架斷裂區域,需要使用焊接操作時,要將機器人模型制作表皮大面積剝開,避免焊接產生的火花或者熱量將考慮海綿填充層引燃。

During the production and maintenance of robot models, attention must be paid to fire prevention and heat protection. In some steel frame fracture areas, when welding operation is required, the robot model production skin shall be peeled off in a large area to avoid sparks or heat generated by welding. The ignition of sponge filling layer shall be considered.

有時候維修機器人模型制作表皮時會遇到表面有水有灰塵的情況，要清理干凈以后再維修，更多相關事項就來我們網站http://m.zzhtdz.com進行咨詢了解吧。

Sometimes when repairing the skin of the robot model, there will be water and dust on the surface. You should clean it before repairing. For more related matters, please visit our website http://m.zzhtdz.com Consult and understand.